Mcoco Safe with Password, Fingerprint and Key Alloy Material Black Finish - MCO/SAFE/BLK/ZE30
Couldn't load pickup availability
Interested? Share on Social Media!
Be the first to know
Safe Code and Sizes
Code | Sizes (LXWXH) |
MCO/SAFE/BLK/ZE20 | 32X22.5X21.5 CM |
MCO/SAFE/BLK/ZE30 | 39.5X32.5X31.5 CM |
MCO/SAFE/BLK/FP340 | 43.5X39.5X21.5 CM |
MCO/SAFE/BLK/ZE50 | 36.5X32.5X51.5 CM |
🔐 Fingerprint Keypad Operation Manual
📌 Product Features
- Default Password: 1234
-
No fingerprint is registered by default.
(Unregistered/"blank" fingerprints cannot open the door.) - IMPORTANT: Before first use, it is strongly recommended to:
- Register your fingerprint.
- Change the default password.
1. 🔓 Unlocking the Safe
Using Password:
- Enter the correct user password and press the # key (e.g., 1234#).
- You will hear two beeps, the green light turns on, and the electromagnet activates for 6 seconds.
- You can now open the door.
Using Fingerprint:
- Place a registered finger on the sensor.
- The green light will turn on and the electromagnet will activate for 6 seconds.
- You can now open the door.
Note: Unregistered fingerprints will not work. Fingerprints must be successfully registered.
2. 🔧 Setting a New Password
- Press the SET button once. The yellow light will turn on.
- Enter a new password (3–8 digits), then press the # key.
- You will hear two beeps and the green light will flash twice, confirming successful password change.
3. 🆕 Registering Fingerprints (Max: 100 fingerprints)
- Press the SET button once. The fingerprint sensor will emit a white light.
- Place the same finger on the sensor four consecutive times.
- On the fourth scan, if the green light turns on and you hear two beeps, the fingerprint is registered successfully.
Note: If registration fails, the sensor will flash red.
4. 🔁 Restore to Factory Settings
- Press and hold the SET button for 3 seconds until you hear a long beep.
- The green LED and fingerprint sensor will light up, indicating the system has been reset.
✅ Default password restored to: 1234
✅ All registered fingerprints are deleted.
5. 🔇 Enable / Disable Sound (Silent Mode)
Enable Silent Mode:
- Press and hold the 3 key for 3 seconds.
- The green light will flash twice – Silent Mode Activated.
Restore Sound:
- Option 1: Press and hold the 3 key for 3 seconds again. You'll hear a double beep and the green light will flash twice – Sound On.
- Option 2: Power off and power on the device – sound is enabled by default.
6. 🔒 System Lock Function
Triggered when:
- Wrong password entered 3 times in a row
- Wrong fingerprint used 5 times in a row
Result:
- The buzzer will sound for 20 seconds
- The system will lock for 20 seconds
- No operations are accepted during this time.
7. 💡 Interior Lighting Function
- After successfully unlocking with password or fingerprint, the interior light turns on and stays on for 30 seconds.
8. 🔋 Low Battery Warning
- If both green and red LEDs light up and the buzzer sounds 5 times after unlocking:
- This indicates low battery.
- Please replace the batteries promptly.
9. 🧭 Single / Double Unlock Mode
Single Mode Unlock:
- Press the 1 key, release it, then press the SET (register) button once.
- A long beep confirms Single Mode is activated (unlock via password or fingerprint).
Double Mode Unlock:
- Press the 2 key, release it, then press the SET (register) button once.
- A long beep confirms Double Mode is activated (requires both password and fingerprint).
⚙️ Product Specifications
Specification |
Value |
Operating Voltage |
4.5–6V |
Low Voltage Threshold |
4.8V (±0.2V) |
Working Current |
380mA (±20%) |
Standby Current |
25μA (±20%) |
❗ Common Fingerprint Issues & Solutions
📌 Issue 1: Fingerprint Registration Fails
- Cause: The Finger did not fully touch the sensor or pressure was too light.
- Solution: Apply gentle, even pressure during registration. Ensure the finger fully contacts the sensor surface.
📌 Issue 2: Fingerprint Recognition Fails for Elderly/Children/Dry Skin
- Solution: Register the same finger 2–3 times to improve accuracy and recognition.